Wednesday, 28 December 2016

HARDNESS TEST

            The hardness of material is its resistance to penetration under a localised pressure or resistance to abrasion. The hardness can be determined by any one of the following tests.

(a) Indentation or Penetration test:
  1. Brinell
  2. Vicker's
  3. Rockwell.

(b) Rebound test.
(c) Scratch test.

BRINELL HARDNESS TEST

This test is used: (1) to determine hardness of metallic materials, 
                             (2) to check the quality of the product,
                             (3) for uniformity of samples of metals, and 
                             (4) for uniformity of results of heat treatment.
              In this test, a standard hardened steel ball is pressed into the surface of the specimen by a gradually applied load which is maintained on the specimen for definite time. The impression so obtained is measured by a microscope and the Brinell Hardness Number (B.H.N) is found out by following equation:

B.H.N = Applied load in KG/Area of impression or indentation of steel ball in m2
             = P/A


Brinell Hardness Tester: Brinell hardness tester is shown in below Fig.




The hardness test is carried out as follows:
  • Place the test sample on the top of the test table and rise it with the elevating screw, till the test sample just touches the ball.
  • Apply the desired load (about 30' diameter of the ball in mm) either mechanically or by oil pressure.
  • The steel ball during this period moves to the position of the sample and makes an impression or indentation.
  • Measure the indentation diameter at two places, either on the screen provided with the machine or by coinciding the two points of a reading microscope.
  • Using above equation, one can calculate BHN after substituting the values of P, D, d.

Precautions:

(1) The Brinell test should be performed on smooth, flat specimen from which dirt and scale have been cleaned.
(2) Successive impressions made too close to one another tend to produce high readings because of work hardening.
(3) The test should not be made on the specimen so thin that the impression shows through the metal nor should impressions be made too close to the edge of a specimen.

Advantages:
  • It is widely applied in the industry due to the rapidity and simplicity with which they may be performed.
  • High Accuracy achieved and due to small size of the impression produced.
  • Also Rockwell hardness number can be converted to Brinell number using special table or chart.
  • It can be used both for hard and soft material.

Disadvantages:
  1. The test machine is very heavy.
  2. The area of indentation is quite large that it affects the surface quality. This is why, some it is considered as a destructive test.
  3. The thickness of the test sample also limits its use, e.g., thin sheets will bulge or be destroyed during the test.
  4. For very hard materials, the test results are unreliable. The ball gets flattened on hard surfaces.
  5. One faces difficulty in measuring the indentation diameter accurately.

VICKER'S HARDNESS TEST

This is similar to Brinell Hardness test, but in this method the drawback of the flattening of the steel ball in testing harder materials is eliminated. It uses a similar relationship and most of the errors and limitations of Brinell Hardness test are eliminated. In this method of hardness testing a diamond square based pyramid indentor with 136° angle between opposite faces is used. The load varies from 5 kg to 120 kg in increments of 5 kg. Similar to Brinell and Rockwell hardness measuring methods, this method also uses the indentation produced by the indentor (Diamond pyramid). The indentor gives geometrically similar impressions under different loads.
A piston and a dash pot of oil is used for controlling the rate and duration of loading. The specimen is placed on the anvil, which is then raised to indentor. Load is applied and then removed. The value of Vicker's Hardness can be obtained by the following relation:

VPN=DPN=
             
                

Where VPN = Vicker's Pyramid Number and
             DPN = Diamond Pyramid Number

Let P is the load applied,
       d is the average length of two diagonals, in mm, and 
       q is the angle between opposite faces of diamond pyramid (136°). Then


              This method is used for the determination of hardness of very thin and very hard materials. This method also facilitates the ease of measurement of a diagonal of the indentation area ( Fig ), as compared to circular dimensions, which are difficult to measure. This method is rapid, accurate and suitable for metals as thin as 0.15 mm. The indentor is capable of giving geometrically similar impression with different loads. Obviously, the hardness number is independent of the load applied. Some typical values of VPN are:

Material
VPN Value (Kg/mm2)


Diamond
8400
Steel
210
Aluminium
22
Lead
12
Tungsten carbide
2100


             The values of Brinell and Vickers hardness are practically the same up to 300. We must note that Vicker's test can be carried out accurately on polished surfaces but does not give accurate results when used for rough surfaces.

VICKER'S HARDNESS TEST

This is similar to Brinell Hardness test, but in this method the drawback of the flattening of the steel ball in testing harder materials is eliminated. It uses a similar relationship and most of the errors and limitations of Brinell Hardness test are eliminated. In this method of hardness testing a diamond square based pyramid indentor with 136° angle between opposite faces is used. The load varies from 5 kg to 120 kg in increments of 5 kg. Similar to Brinell and Rockwell hardness measuring methods, this method also uses the indentation produced by the indentor (Diamond pyramid). The indentor gives geometrically similar impressions under different loads.
A piston and a dash pot of oil is used for controlling the rate and duration of loading. The specimen is placed on the anvil, which is then raised to indentor. Load is applied and then removed. The value of Vicker's Hardness can be obtained by the following relation:

VPN=DPN=
             
                

Where VPN = Vicker's Pyramid Number and
             DPN = Diamond Pyramid Number

Let P is the load applied,
       d is the average length of two diagonals, in mm, and 
       q is the angle between opposite faces of diamond pyramid (136°). Then


              This method is used for the determination of hardness of very thin and very hard materials. This method also facilitates the ease of measurement of a diagonal of the indentation area ( Fig ), as compared to circular dimensions, which are difficult to measure. This method is rapid, accurate and suitable for metals as thin as 0.15 mm. The indentor is capable of giving geometrically similar impression with different loads. Obviously, the hardness number is independent of the load applied. Some typical values of VPN are:

Material
VPN Value (Kg/mm2)


Diamond
8400
Steel
210
Aluminium
22
Lead
12
Tungsten carbide
2100


             The values of Brinell and Vickers hardness are practically the same up to 300. We must note that Vicker's test can be carried out accurately on polished surfaces but does not give accurate results when used for rough surfaces.

TORSION TEST

              The torsion test is carried out to determine the value of modulus of rigidity and ultimate shear strength of a metallic specimen. A schematic diagram of a torsion testing machine is shown in fig. The torsion test is carried out to determine the value of modulus of rigidity and ultimate shear strength of a metallic specimen. A schematic diagram of a torsion testing machine is shown in fig.